mirror of
https://github.com/idanoo/nzart-exam-generator.git
synced 2024-12-04 22:26:58 +00:00
399 lines
7.8 KiB
Plaintext
399 lines
7.8 KiB
Plaintext
|
|
|
|
% FILENAME = N29.TXT
|
|
% Interference and Filtering
|
|
% Release version 4, June 2004
|
|
|
|
%QUESTION: 1
|
|
#29.1 Electromagnetic compatibility is:
|
|
|
|
two antennas facing each other
|
|
|
|
the ability of equipment to function satisfactorily in its own environment without introducing intolerable electromagnetic disturbances
|
|
|
|
more than one relay solenoid operating simultaneously
|
|
|
|
the inability of equipment to function satisfactorily together and produce tolerable electromagnetic disturbances
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 2
|
|
#29.2 On an amateur receiver, unwanted signals are found at every 15.625 kHz. This is probably due to:
|
|
|
|
a low-frequency government station
|
|
|
|
a remote radar station
|
|
|
|
radiation from a nearby TV line oscillator
|
|
|
|
none of these
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 3
|
|
#29.3 Narrow-band interference can be caused by:
|
|
|
|
transmitter harmonics
|
|
|
|
a neon sign
|
|
|
|
a shaver motor
|
|
|
|
lightning flashes
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 4
|
|
#29.4 Which of the following is most likely to cause broad-band continuous interference:
|
|
|
|
an electric blanket switch
|
|
|
|
a refrigerator thermostat
|
|
|
|
a microwave transmitter
|
|
|
|
poor commutation in an electric motor
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 5
|
|
#29.5 If broadband noise interference varies when it rains, the most likely cause could be from:
|
|
|
|
underground power cables
|
|
|
|
outside overhead power lines
|
|
|
|
car ignitions
|
|
|
|
your antenna connection
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 6
|
|
#29.6 Before explaining to a neighbour that the reported interference is due to a lack of immunity in the neighbour's electronic equipment:
|
|
|
|
disconnect all your equipment from their power sources
|
|
|
|
write a letter to the MED
|
|
|
|
make sure that there is no interference on your own domestic equipment
|
|
|
|
ignore all complaints and take no action
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 7
|
|
#29.7 A neighbour's stereo system is suffering RF break-through. One possible cure is to:
|
|
|
|
put a ferrite bead on the transmitter output lead
|
|
|
|
put a capacitor across the transmitter output
|
|
|
|
use open-wire feeders to the antenna
|
|
|
|
use screened wire for the loudspeaker leads
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 8
|
|
#29.8 When living in a densely-populated area, it is wise to:
|
|
|
|
always use maximum transmitter output power
|
|
|
|
use the minimum transmitter output power necessary
|
|
|
|
only transmit during popular television programme times
|
|
|
|
point the beam at the maximum number of television antennas
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 9
|
|
#29.9 When someone in the neighbourhood complains of TVI it is wise to:
|
|
|
|
deny all responsibility
|
|
|
|
immediately blame the other equipment
|
|
|
|
inform all the other neighbours
|
|
|
|
check your log to see if it coincides with your transmissions
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 10
|
|
#29.10 Cross-modulation is usually caused by:
|
|
|
|
rectification of strong signals in overloaded stages
|
|
|
|
key-clicks generated at the transmitter
|
|
|
|
improper filtering in the transmitter
|
|
|
|
lack of receiver sensitivity and selectivity
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 11
|
|
#29.11 When the signal from a transmitter overloads the audio stages of a broadcast receiver, the transmitted signal:
|
|
|
|
can be heard irrespective of where the receiver is tuned
|
|
|
|
appears only when a broadcast station is received
|
|
|
|
is distorted on voice peaks
|
|
|
|
appears on only one frequency
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 12
|
|
#29.12 Cross-modulation of a broadcast receiver by a nearby transmitter would be noticed in the receiver as:
|
|
|
|
a lack of signals being received
|
|
|
|
the undesired signal in the background of the desired signal
|
|
|
|
interference only when a broadcast signal is received
|
|
|
|
distortion on transmitted voice peaks
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 13
|
|
#29.13 Unwanted signals from a radio transmitter which cause harmful interference to other users are known as:
|
|
|
|
rectified signals
|
|
|
|
re-radiation signals
|
|
|
|
reflected signals
|
|
|
|
harmonic and other spurious signals
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 14
|
|
#29.14 To reduce harmonic output from a transmitter, the following could be put in the transmission line as close to the
|
|
transmitter as possible:
|
|
|
|
wave trap
|
|
|
|
low-pass filter
|
|
|
|
high-pass filter
|
|
|
|
band reject filter
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 15
|
|
#29.15 To reduce energy from an HF transmitter getting into a television receiver, the following could be placed in the TV antenna lead as close to the TV as possible:
|
|
|
|
active filter
|
|
|
|
low-pass filter
|
|
|
|
high-pass filter
|
|
|
|
band reject filter
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 16
|
|
#29.16 A low-pass filter used to eliminate the radiation of unwanted signals is connected to the:
|
|
|
|
output of the balanced modulator
|
|
|
|
output of the amateur transmitter
|
|
|
|
input of the stereo system
|
|
|
|
input of the mixer stage of your SSB transmitter
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 17
|
|
#29.17 A band-pass filter will:
|
|
|
|
pass frequencies each side of a band
|
|
|
|
attenuate low frequencies but not high frequencies
|
|
|
|
attenuate frequencies each side of a band
|
|
|
|
attenuate high frequencies but not low frequencies
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 18
|
|
#29.18 A band-stop filter will:
|
|
|
|
pass frequencies each side of a band
|
|
|
|
stop frequencies each side of a band
|
|
|
|
only allow one spot frequency through
|
|
|
|
pass frequencies below 100 MHz
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 19
|
|
#29.19 A low-pass filter for a high frequency transmitter output would:
|
|
|
|
attenuate frequencies above 30 MHz
|
|
|
|
pass audio frequencies below 3 kHz
|
|
|
|
attenuate frequencies below 30 MHz
|
|
|
|
pass audio frequencies above 3 kHz
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 20
|
|
#29.20 Installing a low-pass filter between the transmitter and transmission line will:
|
|
|
|
permit higher frequency signals to pass to the antenna
|
|
|
|
ensure an SWR not exceeding 2:1
|
|
|
|
reduce the power output back to the legal maximum
|
|
|
|
permit lower frequency signals to pass to the antenna
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 21
|
|
#29.21 A low-pass filter may be used in an amateur radio installation:
|
|
|
|
to attenuate signals lower in frequency than the transmission
|
|
|
|
to attenuate signals higher in frequency than the transmission
|
|
|
|
to boost the output power of the lower frequency transmissions
|
|
|
|
to boost the power of higher frequency transmissions
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 22
|
|
#29.22 Television interference caused by harmonics radiated from an amateur transmitter could be eliminated by fitting:
|
|
|
|
a low-pass filter in the TV receiver antenna input
|
|
|
|
a high-pass filter in the transmitter output
|
|
|
|
a low-pass filter in the transmitter output
|
|
|
|
a band-pass filter to the speech amplifier
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 23
|
|
#29.23 A high-pass filter can be used to:
|
|
|
|
prevent interference to a telephone
|
|
|
|
prevent overmodulation in a transmitter
|
|
|
|
prevent interference to a TV receiver
|
|
|
|
pass a band of speech frequencies in a modulator
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 24
|
|
#29.24 A high-pass RF filter would normally be fitted:
|
|
|
|
between transmitter output and feedline
|
|
|
|
at the antenna terminals of a TV receiver
|
|
|
|
at the Morse key or keying relay in a transmitter
|
|
|
|
between microphone and speech amplifier
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 25
|
|
#29.25 A high-pass filter attenuates:
|
|
|
|
a band of frequencies in the VHF region
|
|
|
|
all except a band of VHF frequencies
|
|
|
|
high frequencies but not low frequencies
|
|
|
|
low frequencies but not high frequencies
|
|
|
|
% ans 4
|
|
|
|
%QUESTION: 26
|
|
#29.26 An operational amplifier connected as a filter always utilises:
|
|
|
|
positive feedback to reduce oscillation
|
|
|
|
negative feedback
|
|
|
|
random feedback
|
|
|
|
inductors and resistor circuits only
|
|
|
|
% ans 2
|
|
|
|
%QUESTION: 27
|
|
#29.27 The voltage gain of an operational amplifier at low frequencies is:
|
|
|
|
very high but purposely reduced using circuit components
|
|
|
|
very low but purposely increased using circuit components
|
|
|
|
less than one
|
|
|
|
undefined
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 28
|
|
#29.28 The input impedance of an operational amplifier is generally:
|
|
|
|
very high
|
|
|
|
very low
|
|
|
|
capacitive
|
|
|
|
inductive
|
|
|
|
% ans 1
|
|
|
|
%QUESTION: 29
|
|
#29.29 An active audio low-pass filter could be constructed using:
|
|
|
|
zener diodes and resistors
|
|
|
|
electrolytic capacitors and resistors
|
|
|
|
an operational amplifier, resistors and capacitors
|
|
|
|
a transformer and capacitors
|
|
|
|
% ans 3
|
|
|
|
%QUESTION: 30
|
|
#29.30 A filter used to attenuate a very narrow band of frequencies centred on 3.6 MHz would be called:
|
|
|
|
a band-pass filter
|
|
|
|
a high-pass filter
|
|
|
|
a low-pass filter
|
|
|
|
a notch filter
|
|
|
|
% ans 4
|
|
|
|
|